MT5634ZBA-DIDData/Fax/DID ModemUser Guide
Chapter 3 - Operation10MultiModemDID User GuideChapter 3 – OperationFront Panel of the MultiModemDID ModemThe MT5634ZBA-DID modem has 10 LED indicator
Chapter 3 - Operation11MultiModemDID User GuideDID OperationDirect Inward Dialing (DID) uses an analog trunk line to route several phone numbers to on
Chapter 3 - Operation12MultiModemDID User GuideConnecting to the InternetYour Multi-Tech modem is your gateway to the Internet and the World Wide Web.
Chapter 4 - AT Commands, S-Registers, Result Codes13MultiModemDID User GuideChapter 4 - AT Commands, S -Registers,and Result CodesAT commands are used
Chapter 4 - AT Commands, S-Registers, Result Codes14MultiModemDID User GuideAT CommandsCommand: AT Attention CodeValues: n/aDescription: The attention
Chapter 4 - AT Commands, S-Registers, Result Codes15MultiModemDID User Guide@ Wait for quiet answer. Causes modem to wait for a ringback, then 5 secon
Chapter 4 - AT Commands, S-Registers, Result Codes16MultiModemDID User GuideCommand: MnMonitor Speaker ModeValues:n = 0, 1, 2, or 3Default: 1Descripti
Chapter 4 - AT Commands, S-Registers, Result Codes17MultiModemDID User GuideCommand: T Tone DialingValues: P, TDefault: TDescription: Configures the m
Chapter 4 - AT Commands, S-Registers, Result Codes18MultiModemDID User GuideCommand: &DnData Terminal Ready (DTR) ControlValues:n = 0, 1, 2, or 3D
Chapter 4 - AT Commands, S-Registers, Result Codes19MultiModemDID User GuideCommand: &SnData Set Ready (DSR) ControlValues:n = 0 or 1Default: 0Des
User GuideProduct Number S000234A Revision AMultiModemDID (MT5634ZBA-DID)CopyrightCopyright © 2002 by Multi-Tech Systems, Inc.All rights reserved. Thi
Chapter 4 - AT Commands, S-Registers, Result Codes20MultiModemDID User GuideCommand: \BnTransmit BreakValues:n = 0–9 in 100 ms unitsDefault: 3Descript
Chapter 4 - AT Commands, S-Registers, Result Codes21MultiModemDID User GuideCommand: \NnError Correction Mode SelectionValues:n = 0–5, or 7Default: 3D
Chapter 4 - AT Commands, S-Registers, Result Codes22MultiModemDID User GuideCommand: %A Adaptive Answer Result Code EnableValues:n = 0 or 1Default: 0D
Chapter 4 - AT Commands, S-Registers, Result Codes23MultiModemDID User GuideCommand: %RnCisco ConfigurationValues:n = 0, 1Default: 0Description: %R0 D
Chapter 4 - AT Commands, S-Registers, Result Codes24MultiModemDID User GuideCommand: +DR=nV.44 Data Compression ReportingValues:n = 0 or 1Default: 0De
Chapter 4 - AT Commands, S-Registers, Result Codes25MultiModemDID User GuideSubparametersdirectionSpecifies the DTE direction of the data compression.
Chapter 4 - AT Commands, S-Registers, Result Codes26MultiModemDID User GuideCommand: +MS= Modulation SelectionValues: See description.Defaults: See de
Chapter 4 - AT Commands, S-Registers, Result Codes27MultiModemDID User GuideautomodeAn optional numeric value that enables or disables automaticmodula
Chapter 4 - AT Commands, S-Registers, Result Codes28MultiModemDID User GuideV.92 CommandsCommand: +PCW=nCall Waiting EnableValues:n = 0, 1, or 2Defaul
Chapter 4 - AT Commands, S-Registers, Result Codes29MultiModemDID User GuideCommand: +PMHR=nModem on Hold InitiateValues:n = 0–13Default: 0Description
Contents3MultiModemDID User GuideTable of ContentsChapter 1 - Introduction and Description...
Chapter 4 - AT Commands, S-Registers, Result Codes30MultiModemDID User GuideCommand: +PQC=nQuick Connect ControlValues:n = 0, 1, 2, or 3Default: 3Desc
Chapter 4 - AT Commands, S-Registers, Result Codes31MultiModemDID User GuideEscape CommandsCommand: +++AT<CR> Escape SequenceValues: n/aDescri
Chapter 4 - AT Commands, S-Registers, Result Codes32MultiModemDID User GuideDID CommandsThe MT5634ZBA-DID modem uses *D commands to configure the mode
Chapter 4 - AT Commands, S-Registers, Result Codes33MultiModemDID User GuideCommand: *DT Wait for Digit Time-Out TimeValues:n = 0, 1, 2 or 3Defaul
Chapter 4 - AT Commands, S-Registers, Result Codes34MultiModemDID User GuideCommand: *DF Format for Reporting Incoming DID NumberValues: 0, 1, 2Defaul
Chapter 4 - AT Commands, S-Registers, Result Codes35MultiModemDID User Guide[15:26:52.500] DTMF9[15:26:52.500] DTMF8[15:26:52.500] DTMF0[15:27:06.610]
Chapter 4 - AT Commands, S-Registers, Result Codes36MultiModemDID User GuideS-RegistersCertain modem values, or parameters, are stored in memory locat
Chapter 4 - AT Commands, S-Registers, Result Codes37MultiModemDID User GuideS36decimal 0–7 7 Specifies the action to take in the event of anegotiation
Chapter 4 - AT Commands, S-Registers, Result Codes38MultiModemDID User Guide17 48000 bps18 49333 bps19 50666 bps20 52000 bps21 53333 bps22 54666 bps23
Chapter 4 - AT Commands, S-Registers, Result Codes39MultiModemDID User GuideResult CodesIn command mode your modem can send responses called result co
Contents4MultiModemDID User GuideChapter 6 - Troubleshooting...
Chapter 4 - AT Commands, S-Registers, Result Codes40MultiModemDID User Guide100 CONNECT 28000 *Connected at 28000 bps, 56K rate101 CONNECT 29333 *Conn
Chapter 5 - Remote Configuration41MultiModemDID User GuideChapter 5 - Remote ConfigurationRemote configuration is a network management tool that allo
Chapter 5 - Remote Configuration42MultiModemDID User GuideChanging the Remote Escape CharacterTo increase security, you can change a remote modem’s r
Chapter 6 - Troubleshooting43MultiModemDID User GuideChapter 6 - TroubleshootingYour modem was thoroughly tested at the factory before it was shipped.
Chapter 6 - Troubleshooting44MultiModemDID User GuideThe Modem Dials But Cannot ConnectThere can be several reasons the ZBA fails to make a connection
Chapter 6 - Troubleshooting45MultiModemDID User GuideThe Modem Disconnects While Online•If you have Call Waiting on the same phone line as your modem,
Chapter 6 - Troubleshooting46MultiModemDID User GuideDID Troubleshooting•Make sure that the MT5634ZBA-DID parameters match the DID line. Refer to the
Appendix A – Regulatory Compliance47MultiModemDID User GuideAppendix A – Regulatory ComplianceFCC Part 68 Telecom1. This equipment complies with part
Appendix A – Regulatory Compliance48MultiModemDID User GuideFCC Part 15This equipment has been tested and found to comply with the limits for a Class
Appendix B – Technical Specifications49MultiModemDID User GuideAppendix B – Technical SpecificationsYour MultiModemZBA-DID fax modem meets the followi
Chapter 1 - Introduction and Description5MultiModemDID User GuideChapter 1 - Introduction and DescriptionWelcome to the world of data communications.
Appendix C – Warranty and Service50MultiModemDID User GuideAppendix C - Warranty and Repairs Multi-Tech Systems, Inc. Warranty and Repairs PoliciesWar
Appendix C – Warranty and Service51MultiModemDID User GuideRepair Procedures for International Customers (Outside U.S.A. and Canada)Your original poin
Appendix D – Upgrading the Modem’s Firmware52MultiModemDID User GuideAppendix D - Upgrading the Modem’sFirmwareUpgrade Overview1. Identify your modem’
Appendix D – Upgrading the Modem’s Firmware53MultiModemDID User GuideStep 4: Extract the Upgrade Files1. Install the Flash Wizard utility by double-cl
Appendix E – Installng a Modem Under Linux54MultiModemDID User GuideAppendix E - Installing a Modem UnderLinuxIntroductionThis appendix explains how t
Appendix E – Installng a Modem Under Linux55MultiModemDID User GuideCalling the ISP1. On the Task Bar at the bottom of the screen, select the Gnome Fo
Appendix F – Technical Support56MultiModemDID User GuideAppendix F - Technical SupportMulti-Tech Systems, Inc. has an excellent staff of technical sup
Index57MultiModemDID User GuideIndexSymbols11-bit mode 2356K operationdigital loss when used withPBX 38disabling the auto rate 38maximum conn
Index58MultiModemDID User GuideDdata buffering 18data calling tone 36Data Calling Tone command 21Data Carrier Detect command17data compressio
Index59MultiModemDID User Guideremote configuration 41escape character 36, 42escape sequence 31remote node operation 12Removing a modem fr
Chapter 1 - Introduction and Description6MultiModemDID User GuideWe Supply• An MT5634ZBA-DID modem• A set of four self-adhesive plastic feet• A power
Chapter 2 - Installation7MultiModemDID User GuideChapter 2 - InstallationStep 1: Assemble the ModemThe only assembly required is to mount the feet on
Chapter 2 - Installation8MultiModemDID User Guide(Optional) Connect the Modem to the PhoneFor voice-only calls, plug a phone into the modem’s PHONE ja
Chapter 2 - Installation9MultiModemDID User GuideFrom Windows 2000, XP1. Click Start | Settings | Control Panel.2. Double-click the Phone and Modems i
Commenti su questo manuale