Multitech CDMA Specifiche Pagina 93
- Pagina / 129
- Indice
- SEGNALIBRI
Valutato. / 5. Basato su recensioni clienti
Chapter 15 – Audio Commands
Multi-Tech Systems, Inc. CDMA C1 AT Commands Reference Guide 93
Values: <Level>
0
-84dB (no output)
1
-32dB
2
-28dB
3
-24dB
4
-20dB
5
-16dB
6
-12dB
7
-8dB
8
-4dB
9
0dB (default)
10
4dB
11
8dB
12
12dB
If no argument is supplied to the command, the default value is assumed. The configuration is
saved immediately. See the Audio Overview section for more information.
Special
Considerations:
The +CLVL gain value is added onto the +WDGR gain. Depending on the gain setting of +WDGR,
the full range of the +CLVL command may not be realized.
Example: If +WDGR is set to +12dB gain, the +CLVL command cannot add any more positive gain. Setting
the +CLVL command to +12dB gain would not yield a total of +24dB gain, since the gain stage
can only supply a maximum of +12dB gain.
The following formulas govern the total digital receive gain:
Total Gain = (WDGR Gain + CLVL Gain)
-84dB <= Total Gain <= +12dB
Initialize Voice Parameters +VIP
Description: This resets audio parameters back to factory default values.
The following parameters are restored:
Gain control (+VGR, +VGT)
Speaker & microphone selection (+SPEAKER)
Echo cancellation (+ECHO)
Side tone selection (+SIDET)
Digital gain (+WDGT, +WDGR)
Microphone gain enable (+MGE)
Loudspeaker volume level (+CLVL)
Syntax: AT+VIP
Command
Possible Responses
AT+VIP
OK
Note: Command valid
- CDMA-C1 AT Commands 1
- Copyright 2
- Trademarks 2
- Revisions 2
- Contacting Multi-Tech 2
- Contents 3
- Contents 4
- Document Scope 9
- Related References 9
- Serial Interface Settings 10
- Overview 10
- Terminology 11
- Command Format and Syntax 11
- Command-Line Editing 12
- Input Command Syntax 12
- Other Syntax 12
- Output Response Syntax 12
- Parameter Defaults 13
- Unsolicited Message Syntax 13
- Attention AT 14
- Repeat Last Command A/ 14
- Echo E 14
- +WUSLMSK 15
- Syntax: AT+WPRI? 16
- Hardware Version +WHWV 17
- Capabilities List +GCAP 19
- Subscriber Number +CNUM 19
- Save Configuration &W 21
- General Indicator +WIND 22
- Result 23
- Examples: +WIND: 4 23
- Error Codes: 24
- Chapter 7 – Status Commands 25
- Fixed DTE Rate +IPR 28
- Set DCD Signal &C 29
- Set DTR Signal &D 29
- Set DSR Signal &S 30
- Syntax: AT+DR=<val> 31
- Syntax: AT+WCHD 31
- Automatic Answer S0 32
- Command Edit Character S5 33
- Dial Command D 35
- Hang-Up Command H 36
- Answer a Call A 36
- Syntax: ATA 37
- Incoming Call +RING 38
- Emergency Mode +WSOS 40
- Call Answered +WANS 41
- Call Connected +WCNT 41
- Call Ended +WEND 42
- Call Originated +WORG 43
- CPHS Command +CPHS 43
- Values: <LineId> 44
- Examples: 44
- Call Forwarding +CCFC 45
- Syntax: AT+WFSH 46
- Unsolicited 46
- Send DTMF Tones +VTS 47
- Serving System +CSS 49
- Signal Quality +CSQ 50
- Band Preference +WBND 53
- Service Indication +WSRV 53
- Roam Preference +WRMP 54
- Default Cell Band +WDCB 55
- Roaming Indication +WROM 55
- Values: <indicator> 56
- Values: <mode> 58
- Excess SPC Failures +WLCK 60
- Commit Changes +WCMT 61
- Set IMSI +WIMI 62
- SID and NID +WSID 63
- Commit Successful +WOTC 66
- SPL Unlocked +WOTS 66
- NAM Download OK +WOTN 66
- MDM Download OK +WOTM 67
- IMSI Download OK +WOTI 67
- PRL Download OK +WOTP 67
- Values: <Mode> 74
- Parameter 74
- Send Message +CMGS 75
- Read Message +CMGR 76
- List Message +CMGL 77
- Delete Message +CMGD 79
- Syntax: +WMGF 84
- Audio Subsystem Overview 85
- Chapter 15 – Audio Commands 86
- Microphone Gain +VGT 87
- Speaker Gain Control +VGR 88
- Values: <Gain> 89
- Digital Gain Receive +WDGR 90
- Values: <val1> 91
- Echo Cancellation +ECHO 92
- Audio Loopback &T 94
- Quick Net Connect $QCQNC 95
- R-SCH Selection $QCMIP 96
- MIP Selection $QCMIPP 96
- Chapter 16 – Data Commands 97
- Configure TCP/IP +WIPCFG 99
- Values: <cmdtype> 101
- Bearer Status +WIPBR 102
- Values: <protocol> 103
- Response 105
- Syntax: AT+WIPERR? 105
- Values: 107
- Options and 107
- 32kHz Sleep Mode +W32K 110
- Chapter 18 – Sleep Commands 111
- Syntax: +WNETTIMEGET? 112
- Response Field 112
- Description: 112
- Introduction 113
- Acquiring Cellular Service 113
- Call Processing 114
- Sending Binary Data 115
- TCP Socket Examples 116
- TCP Client Socket Connection 117
- TCP Server Example 117
Prodotti e manuali riguardandi Networking Multitech CDMA
Networking Multitech MT2834BA Manuale Utente
(7 pagine)
(7 pagine)
Networking Multitech MT2834BL Specifiche
(225 pagine)
(225 pagine)
Networking Multitech MT56DSU-R Manuale Utente
(11 pagine)
(11 pagine)
Networking Multitech MTSMC-C-N3 Manuale Utente
(14 pagine)
(14 pagine)
Networking Multitech MT2834ZDX Manuale Utente
(20 pagine)
(20 pagine)
Networking Multitech MVP30-60 Manuale Utente
(4 pagine)
(4 pagine)
Networking Multitech MULTIVOIP MVP-810 Guida Utente
(163 pagine)
(163 pagine)
Networking Multitech FF830 Guida Utente
(151 pagine)
(151 pagine)
Networking Multitech MTR-C2 Manuale Utente
(20 pagine)
(20 pagine)
Networking Multitech GFU19 Manuale Utente
(210 pagine)
(210 pagine)
Networking Multitech MTCMR-H Guida Utente
(147 pagine)
(147 pagine)
Networking Multitech MTSMC-C-N3 Manuale Utente
(24 pagine)
(24 pagine)
Networking Multitech MT56DSU-R Specifiche
(230 pagine)
(230 pagine)
Networking Multitech MTR-H6 Guida Utente
(25 pagine)
(25 pagine)
© 2020, manymanuals.it. Tutti i diritti riservati | 0.054 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commenti su questo manuale