Multitech FR221 Guida Utente Pagina 60
- Pagina / 113
- Indice
- SEGNALIBRI
Valutato. / 5. Basato su recensioni clienti
60
MultiFRAD User Guide
Congestion Management, Mode, and CIR/Be settings are used to avoid congestion and possible loss
of data. The Committed Information Rate (CIR) and Excess Burst rate (Be) settings are throughput
amounts determined by the network and user when each DLCI is ordered. The CIR is the basic
throughput which the network will try to set aside for that DLCI. It will always be equal to or less than
the actual access rate of the physical line (i.e., if the frame relay physical link is a 56K DDS line, the
sum of the CIRs of all DLCIs on that link should not exceed 56K bps). The Be is the excess burst
throughput rate (added to CIR) that the network should accept for that DLCI before significant loss of
data occurs due to the discarding of frames during times of congestion. Note, however, that in frame
relay there is no absolute guarantee of a congestion-free link, regardless of CIR and Be settings. The
CIR and Be settings on the MultiFRAD should match the settings that the network has provisioned.
The Congestion Management and Mode settings determine how the MultiFRAD handles congestion.
The Mode selects whether the MultiFRAD should use its own throughput calculations to avoid
congestion, or simply send data to the network as fast as possible. The MultiFRAD calculates
throughput after every CIR Measurement Interval, and can limit throughput to either the CIR (Adhere
to CIR) or the CIR plus the Be (Adhere to CIR+Be). The Congestion Management setting selects
whether the MultiFRAD should stop sending data when congestion is indicated (Stop and Start), or
gradually reduce throughput during times of congestion (Throttle Up and Down).
Compression can be enabled on a per-DLCI basis by clicking on the Others-Compression box. If
compression is required, it must be enabled on both the local and remote ends of the PVC.
To map a protocol to a DLCI (e.g., 17), return to the MF200 main menu and then click the protocol
stack that you are using. In the lower left part of the protocol stack dialog box a list of Logical WANs
is displayed. To add a new logical WAN, click the Add (+) button and the next logical WAN number
will appear in the list on the left hand side of the dialog box.
For example let’s map our new DLCI 17 to the IP protocol as a WAN 2 with an IP Port Address of
192.168.2.1, an IP Mask of 255.255.255.0, and a remote IP Address of 192.168.2.2. From the MF200
main menu, click the IP button. The IP Setup dialog box is displayed. Click the WAN tab at the top of
the dialog box. The WAN parameters are displayed. Click the Add (+) button and WAN 2 is added to
the List of Logical WANs. Default IP addresses will be displayed for the Port Address and Remote
Address and a default IP Mask will appear in its window. If either address or mask needs to be
changed, click the appropriate window and the change the numbers.
- MultiFRAD 200-Series 1
- Models FR221 & FR221/V2 1
- User Guide 1
- Contents 3
- Appendixes 4
- Preview of this Guide 7
- Front Panel Description 8
- Back Panel Description 10
- Technical Specifications 12
- Chapter 2 - Installation 13
- Introduction 14
- Safety Warning Telecom 14
- Lithium Battery Caution 14
- Unpacking your MultiFRAD 15
- Cabling your MultiFRAD 16
- V.35 Shunt Procedure 18
- Jumper Block 20
- In Position 2 20
- (Default) 20
- Installing Your Software 22
- Click Yes to continue 24
- Ethernet Setup 25
- WAN Port Setup 27
- Data Ports Setup 28
- DLCI Setup 29
- Voice/Fax Channel Setup 30
- Detect and Map Your DLCIs 33
- Before You Begin 40
- MultiFRAD Configuration 41
- Changing IP Parameters 42
- Changing IPX Parameters 44
- Spanning Tree Setup 46
- Filtering 46
- Statistics 47
- IP Statistics 48
- IPX Port Statistics 49
- SNMP Statistics 50
- WAN Statistics 50
- Frame Relay Statistics 51
- Data Port Statistics 52
- Frame Relay 55
- Point-To-Point 56
- Point to Point Setup 57
- Frame Relay Setup 58
- Packet Priority 62
- Data Port Configuration 63
- Interface 64
- Auto Call 65
- Voice/Fax (FR221/V2 only) 66
- Regional (FR221/V2 only) 67
- Phone Book 68
- Delete(-) 69
- Others Setup 70
- Enable Logging of Statistics 71
- Enable Analysis of Statistics 72
- Remote Configuration 74
- Modem-Based 74
- LAN-Based 76
- Remote Management 77
- Web Browser Management 79
- Limited Warranty 82
- On-line Warranty Registration 82
- Tech Support 83
- The Multi-Tech BBS 85
- To Download a File 85
- About the Internet 86
- Appendix A - Cabling Diagrams 88
- Command Port Cable 88
- LAN Cable 88
- DSU Cable 88
- Voice/Fax Channel Connectors 89
- Trunk Cable 90
- Class A Statement 91
- Fax Branding Statement 91
- FCC Part 68 Telecom 92
- Canadian Limitations Notice 93
- Appendix C - Network Overview 94
- Network Address 96
- Internet Protocol (IP) 96
- IP Addressing 97
- 12345678 98
- MultiFRAD User Guide 100
- Glossary 101
- MultiFRAD II User Guide 112
Prodotti e manuali riguardandi Networking Multitech FR221
Networking Multitech MT5634ZLXE Guida Utente
(12 pagine)
(12 pagine)
Networking Multitech MT5634IND Specifiche
(23 pagine)
(23 pagine)
Networking Multitech MT5600SMI Guida Utente
(30 pagine)
(30 pagine)
Networking Multitech ISIHP-4U Manuale Utente
(17 pagine)
(17 pagine)
Networking Multitech RF760VPN Manuale Utente
(4 pagine)
(4 pagine)
Networking Multitech MT5600SMI-32 Specifiche
(115 pagine)
(115 pagine)
(71 pagine)
Networking Multitech E Specifiche
(34 pagine)
(34 pagine)
Networking Multitech MTCBA-C-N12 Manuale Utente
(17 pagine)
(17 pagine)
Networking Multitech MTSMC-G-F1 Specifiche
(26 pagine)
(26 pagine)
Networking Multitech BL-Series Manuale Utente
(60 pagine)
(60 pagine)
Lanner Počítačový hardware uživatelské příručky
Seznam produktů Lanner Počítačový hardware obsahuje 79 uživatelské příručky pro 79 modelů. Všechny uživatelské příručky pdf jsou k dispozici ke stažení nebo prohlížení online.
© 2020, manymanuals.it. Tutti i diritti riservati | 0.016 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commenti su questo manuale